d-24 - Process Equipment Parts

Part List

d-17: Current when faults happen
0 ● U3-33 Rated motor power 1-1000 KW ● Depending on
U3-28
frequency for the
7:38400
U3-30 Detect value for
speed)Protection Current
Standard protocol address 0-247
Invalid DI2
20.0-1000.0 % 100.0 ○ U3-41 Quick current limit 0: OFF
Level Note
0-100.0
with the same
1: ON 1
Parameters displayed
communication
120-150 % 130 ○ U3-43 Overcurrent Stall Speed
delay 0.0-3600.0 s 0.0 ○ U2-24
distributed
control
1 ● U3-55
0.0 represents
Code
motor type
delay
0.0-3600.0 s 0.0 ○ U2-25 Relay1 output
U3-37 Rated motor frequency 5.00-200.0 Hz ● Depending on
0: OFF
Invalid DI3
50-200
1:Permanent
2 Proportionality Factor 0.0-50.0
do not recognize
type ● Depending on
d-02: Bus voltage
150
d-14:The second fault type
d-27: C1 current
S 2.0
0: OFF
1:ON
5:9600
5 ● U3-09
the pumps
U3-19 Sleeping Delay Time 1.0-200.0 s 10.0 ○ U3-20 1 Proportionality Factor 0.0-50.0 15.0 ○ U3-21 1 Integral Time 0.1-100.0
d-10: V input voltage value
under stop status
d-15:The third fault type
version
0: Switch pump
happen
synchronous motor torque
U3-36 Rated motor current 0.1-1000.0 A ● Depending on
Mo output
type ● U3-13 Torque Enhancement 0-20.0 %
running time(0-65535H)
Gain
3.Only
d-19:Internal
address.
Valid DI3 input
1 ● U3-02 Alternation time 0-60000 min 480 ● U3-03 Auxiliary drive quantity 0-4 0 ● U3-04 Multi-pump control
15 ○ Only for V76
0: closed
version
1=busbar
d-07:Set speed
d-01: Output current
mode
100.0-200.0 % 160 ○ U3-45
1: ON
Low Voltage Protection
magnet
4.Master/slave
rpm ● Depending on
5: 9600
d-09:Accumulated power-on time(0- 65535H)
d monitoring parameters group
U3-11
1:Synchronous
Function
15=pressure
d-06: Feedback pressure
0.0-100.0 % 5.0
0.0-3600.0 s 0.0 ○ Relay TA/TB/TC
U3-32
0: master-slave
input delay 0.0-3600.0 s 0.0 ○ U2-23
0: OFF
d-08:Accumulated
1 ●
19 / 21
d-13:The first fault type
2=busbar
based on time
changeover not
0.0-3600.0 s 0.0 ○ U2-20
d-05: Set pressure
1: start and stop
U3-27
U3-18
disconnection of sensor
d-03: Temperature
motor type
3~5 for slave
11=pressure
0.0-3600.0 s 0.0 ○ U3 Advanced Parameters Group
21 / 21
s 20 ○ U3-44 Overcurrent (stall
1: ON
Motor type 0: asynchronous
under running status
6 ● U3-01 Address
starts 0.1-30.0 s 20 ● U3-08 Standard baud rate
drive. 1,2 for master
voltage
d-18: Bus voltage when fault occur
U3-05 Pump-adding delay 0.1-600.0 s 1.0 ● U3-06 Pump-reducing delay 0.1-600.0 s 0.1 ● U3-07 Delay of standy master
method
U3-34 Rated motor speed 1-10000
13=temperature
on ground when power on
control
Input phase loss
U3-00 Baud rate for
d-00: Output frequency
0.0-3000.0
U3-38 Output phase loss
protection option
1 ● U3-10
motor type
2.Evently
d-16:Fault frequency
motor
Protection Voltage
Diviation of PID change 0-100
last two pumps
2 Integral Time 0.1-100.0
U3-31 Time for detecting
20 / 21
output current,
Current
U3-17 Upper limit of
protection
0=running freq.
s 1.5 ○
1:ON
synchronous
motor type
1 ○ U3-40 Motor overload gain
Description Set Range Unit Default Modification
70.0-100.0 % 100.0 ○ U3-46 Auto fault reset times 0-20 3 ○ U3-47 Fault reset Interval time 0.1-100.0 s 10.0 ○ U3-54 Sleep section
delay
d-20: Fault time
pump based on
value
voltage 4=
d-28: Version
U2-21
11 ○ Only for V76
Parameters displayed
6: 19200
Temperature when faults
s 10.0
delay 0.0-3600.0 s 0.0 ○ U2-22
happen
d-24: Output torque
s 10.0 ○
Motor
protection
d-11:C input current
% 60.0
disconnected sensor
Protection for short circuit
4:Change over
1-16 Motor
d-21:Feedback pressure when faults
motor type
0= set frequency
d-04: Set pressure-current pressure
1 ○ U3-42 Overvoltage (stall speed)
drive
input delay
U3-26
U3-12 Carrier Frequency
frequency for all
U3-35 Rated motor voltage 1-800 V ● Depending on
6:19200
0 ●
relay output
7:38400
add pump
d-12:DI input

Sourcing Information

For quotation, datasheet requests or bulk order inquiries:
- Email: qinmao@qinmaocrane.com
-
- Please provide: exact brand, part number, quantity and application details.

Contact QINMAO

Phone: +86-16768798955
Email: qinmao@qinmaocrane.com
Website: www.qinmaocrane.com